Last Updated on August 15, 2023 by River Tree Farms
Bosch dishwashers are some of the best and most reliable in the market; they leave the dishes clean and dried correctly. Nevertheless, as with other household appliances, they may have issues such as stopping mid-cycle.
You are here because you are looking for a substantial solution to fix why the bosch dishwasher stops mid-cycle, and this article will enlighten you on the possible reasons for your dishwasher stopping and help you through it.
The Bosch dishwasher stopping the mid-cycle is very frustrating for anyone using it. You might wonder why your dishwasher stops mid-cycle; various reasons may cause a dishwasher to stop working mid-cycle; check out why.
A dishwasher stops working because it refuses to run or even start while connected to a power supply. Various reasons could cause this: the thermal fuse is blown, the electric control board is now defective, there is a problem with the door latch assembly, and the selector switch needs to be replaced.
Why Does My Bosch Dishwasher Stops Mid-cycle?
Several reasons and causes that lead to your Bosch dishwasher stopping mid-cycle. The many questions running through your mind about the dishwasher stopping mid-cycle are ending in the next few minutes after reading this whole piece. You are not alone; that’s why you are covered here.
Below are various reasons that contribute to your Bosch dishwasher not working.
- The door latch is not fully engaged, so the door is not entirely shut. You need to check the locks, so they are not loose and cause the dishwasher to stop after a few minutes when the door is not closed correctly.
- The dishwasher’s drainpipe or cleaning valve may be clogged, resulting in the dishwasher stopping mid-cycle or even stopping working. When you put them in the dishwasher, this may result from leaving leftovers in your dishwasher. Avoid leaving bits in your dishes, and rinse them before putting them in the Bosch dishwasher. There is water at the bottom of the Bosch dishwasher because the water pump or the filter is clogged.
- The water level is below the optimal water level marked, meaning that it is not enough, which will cause the dishwasher to start and stop after a few minutes.
- Blown fuse. The dishwasher’s thermal fuse may have been blown, or there is a tripped circuit breaker in your dishwasher; hence power may not flow to the appliance.
- The electronic control board may be faulty. After some use, the control board running your appliance may start malfunctioning, leading it to stop the mid-cycle and beep, meaning there is an error.
- The fan assembly may be defective. When this happens, the dishwasher is stuck in the wash cycle; therefore, it does not fully dry the dishes, skips the drying cycle, and stops after the wash cycle.
- If the power supply is cut mid-cycle or the water supply is interrupted mid-cycle, the appliance will start and then stop.
Sometimes a Bosch dishwasher may need a reset for reasons such as clearing an error message, adding another dish, waking up a frozen display, or changing some settings mid-cycle. To reset, you need to try the following procedures, which are either using the Bosch dishwasher’s display or doing it manually;
1. Open the door to reach the dishwasher’s buttons. According to the appliance’s design, you must be cautious as it won’t completely stop working when the door is opened and may result from the hot water inside scalding your hand.
2. Hold the start button until the ‘Active’’ light dims.
3. Let the water drain from the dishwasher. Here, if you are trying to add or remove a dish, you have to wait for about a minute before opening the door as the water may spill out from the front.
4. Press the start button by tapping it as usual, and it will begin the cycle again from the start.
5. Hold the start button for about three seconds.
6. Press the start and On /Off buttons simultaneously after an outage. When the power goes out and comes back, you may have to rest your Bosch dishwasher. Press the two buttons simultaneously and then let the buttons go.
7. You can reset your Bosch dishwasher manually by unplugging the appliance from its power source. You need to be careful and ensure that the cord is not wet to avoid electrocution.
8. You can also turn off the circuit breaker to cut the power supply to the appliance. Wait for two to three minutes before switching the fuse back on.
9. Fix the E-15 error by unplugging and tilting the machine. E-15 type of error is caused by water getting in contact with a sensor on the bottom of the washer. Unplug the dishwasher, check for any broken pipes or valves, then tilt the machine back to the wall; if there are none, plug it back in.
There are two ways you can stop a Bosch dishwasher from stopping mid-cycle.
1. Open the door or latch slightly and wait a few minutes for its operations to stop and for the water to drain.
- Open the dishwasher’s door slightly to expose the control panel.
- Press and hold the ‘Start /Reset’ button for a few seconds, about five seconds.
- Close the dishwasher door.
- The Bosch dishwasher will beep to signal that it is draining.
How Do You Fix A Dishwasher That Stops mid-cycle?
You need to ensure that the door latch is fully engaged to shut appropriately. You need to check the locks so they are not loose and cause the dishwasher to stop after a few minutes when the door is not closed correctly. If the latch is faulty, you should replace it to enable the Bosch dishwasher to work correctly and effectively.
1. The fan assembly may be defective, which is solved by repairing it because it is vital in drying the dishes. When it is faulty, the dishwasher is stuck in the wash cycle, leaving the dishes wet after washing them, skipping the drying cycle, and stopping after the wash cycle.
2. Replacing the blown fuse or thermal fuse. The dishwasher’s thermal fuse may have been blown, hence the appliance’s inadequacy.
3. There is a tripped circuit breaker in your dishwasher; hence power may not be flowing to the appliance. Here, you need to reset it manually. Unplug the dishwasher from the power, and rectify the problem after waiting for about five minutes before switching the fuse back on.
4. The Bosch dishwasher is clogged; the food particles clog the water pump, filter, or drainpipe. Rinsing your dishes before putting them in the dishwasher to prevent clogging since there are no particles on the plates. You should also clean it. The cleaning process that will avoid clogging or help unclog the already clogged filter is:
- Removing the dishwasher’s bottom rack.
- Rotate the filter knob to the left and lift it to remove it.
- Remove the filter from the mesh screen and rinse both separately under running water.
- Scrub the filter and screen with dish detergent and a soft brush to get rid of the remaining food debris.
5. Suppose the power supply is cut mid-cycle or the water supply is interrupted mid-cycle. In that case, the appliance will start and then stop, and you should rectify this by restoring the power supply and the water supply for the cycle to go on.
6. Fix the defective electric control board. The control board is entirely in charge of running your Bosch dishwasher; when it is faulty, the dishwasher will not work effectively. You should get an electrician to repair or replace the control board.
Alternatively, you can fix it on your own if you’re well versed with electric wires but be careful to avoid electrocution. Ensure the water level is at the marked optimal level of the Bosch dishwasher. When there is not enough water, the dishwasher will start and then stop mid-cycle again.
If your Bosch dishwasher stops mid-cycle, you probably need an electrician’s services. However, some of the issues may be minor. The appliance may need a rest for some time, either manually by unplugging it from the power supply or by using the display options on the control panel.
To avoid clogging, you should also note that rinsing the dishes is essential before putting them in the dishwasher. Ensure that the power supply and water supply are uninterrupted to avoid the Bosch dishwasher starting and then stopping mid-cycle.
If your dishwasher keeps beeping and stopping, it is probably because the door latch is loose and the sensor on the door latch is obscured or short-circuited.
If you’ve tried all these resetting procedures without success, you need professional help. It is necessary to ask a professional electrician for the required services or call your manufacturer for better guidance on how to do it.