Last Updated on May 19, 2023 by River Tree Farms
If you are looking for information about the whirlpool dishwasher f6 e6 error code, you are right where many people have found help for the same problem. So, this post will discuss how to fix and resolve the whirlpool dishwasher f6 e6 error code.
Why did the whirlpool dishwasher f6 e6 error code come up? There are 2 main reasons: The control board does not detect water entering the dishwasher, or the water is not heating up as required. Though not typical, it is also likely that the control board is defective.
Unfortunately, the dishwasher will not be functional until the error code disappears from the display. In most cases, fixing the whirlpool dishwasher error codes does not need professional help but a quick-home fix.
This post will discuss how to fix and resolve the whirlpool dishwasher f6 e6 error code.
What Does F6 E6 Mean On Whirlpool Dishwasher?
It means a problem with the amount of water getting into your whirlpool dishwasher. It is a significant issue that needs urgent attention since the main component of dishwasher use is water. The other problem we will also discuss in detail is the water temperatures in the dishwasher during the cycle.
So why is the F6 E6 error code occur on the whirlpool dishwasher?
1. Water Supply Issue
The e6 error code pops up on the display when the control board does not receive enough-water flow or signal in the dishwasher. The problem can be with the dishwasher or with the home water supply.
Let us quickly look at how the water gets into the dishwasher so that you can figure out where the problem lies:
- The tap connects the dishwasher through the dishwasher’s hose pipe.
- The hose pipe connection to the dishwasher is an inlet valve.
- This inlet valve opens to receive enough water for the whirlpool dishwasher’s cycle. The water enters with high pressure.
- It automatically closes once the water in the dishwasher is sufficient.
Referring to this are two possible reasons why your Whirlpool dishwasher has an F6 E6 code:
2. Leaking hose pipe
If the hose pipe connecting the tap to the dishwasher leaks some water somewhere along the way, the inlet valve will not receive enough water from supplying to the dishwasher.
3. Faulty whirlpool water inlet valve
There is no way the water will enter the dishwater if the valve is not opening and closing as it should. The valve may be broken, or the electrical connection may be loose or faulty. If the valve is not working, the whirlpool water inlet valve will need a replacement.
When you open the control panel, you will be able to tell whether it is a loose wire connection causing the problem with the water inlet valve.
4. Water temperatures issues
The e6 error code whirlpool washer may appear if the water is not getting hot properly. The dishwasher operates the cycle when the water is desirable at a boiling point to perfectly clean and sterilize the dishes.
The water not heating correctly results from a malfunctioning whirlpool heating element. The motor supplying power to the heating element is maybe faulty or the heating element itself.
You may need an expert to help you identify this. If there is a problem, then either of them needs a replacement.
5. Faulty Control board
Being the brain of the whirlpool dishwasher, it will randomly bring whirlpool dishwasher error codes when the control board is faulty. Maybe this time, the control board thinks there is not enough water inlet in the dishwasher, whereas you can tell the water inlet is good.
Before you think of replacing the control board, you can start with the whirlpool dishwasher reset.
How to fix the f6 e6 error on the Whirlpool dishwasher?
Replace the water inlet valve if faulty:
How do you replace the whirlpool water inlet valve?
- Unplug the dishwasher from the power source.
- Turn off the water supply.
- Insert the knife under the panel on both sides so that you can release the spring clips.
- Pull the panel forward and remove it.
- Disconnect the wire connectors from the control board, marking for easy return.
- Remove the water supply lines from the valve.
- Now remove the screws to unmount the water inlet valve.
- Install the new whirlpool water inlet valve.
- Repeat the procedure in reverse for installation.
- Replace the whirlpool heating element or the motor powering the whirlpool heating element.
Reset the whirlpool dishwasher to keep the control board updated:
How do you reset a whirlpool dishwasher?
- Unplug the dishwasher from the power source.
- Please leave it to rest for 5 minutes.
- Plug it back.
You can also reset the whirlpool dishwasher by:
- Disconnecting it from the power source at the circuit breaker.
- Let it rest for 2-5minutes.
- Connect the circuit breaker back.
Frequently Asked Questions (FAQs)
How much does a whirlpool dishwasher water valve cost?
Depending on the whirlpool dishwasher model, an inlet valve price ranges between $50-$100.Whirlpool spare parts are available widely and are of good quality and durable.
Where is the whirlpool water inlet valve located?
At one of the corners, right or left behind, the lower part of the kickplate panel. After lifting off the board, you must remove two screws mounting the water inlet valve in place.
What does F6 mean on a whirlpool dishwasher?
It means that the control board has detected that the water is not flowing into the dishwasher as expected. The water level is too low to support a whirlpool wash cycle.
If you own a whirlpool dishwasher, you must be familiar with the F6 error code. Many people will ignore this code, thinking it’s okay, only to realize their dishes are not clean. Yes, because the whirlpool dishwasher F6 E6 Error code pops in the control panel when less water enters the dishwasher. The spray arms will not exert pressure to clean the dishes sufficiently.
If your Whirlpool dishwasher F6 E6 error has not been fixed by the solutions provided in this article, then you have no choice but to contact customer service to fix the problem before it escalates.